kenmore elite electric he3 model 110-82822102 wont heat!

My dryer went on the fritz yesterday...no heat. Everything else works...I tried cutting power to re-set, checking for plugs, and using different heat settings and swithching between manual and auto dry...nothing. Any ideas?? I am pretty good DIY, but not with electricity and meters, just don;t know how they work!...... remove the front lower panel and then unplug dryer and measure resistance at heater element. should be 10 ohms. if thats ok then its most likely the thermal cut off at the rear of the heater box. should be about 0 ohms. Checking for plugs? You mean as in lint? I was thinking electrical plugs. But that (lint) is probably what you meant. Check for 240 volts at the recepticle first. Dryers can turn on 120. Many people that have fuses rather than circuit breakers have spent time needlessly diagnosing, only to find one of the 2 fuses burned. I have breakers, they are fine..and yes plugged lint...have the lower panel off...TONS of lint in there...probably a cause at some point...ohms, volts, etc....I am not well versed in these, but could be....ohms are a popular venacular here, and I understand resisitance....no power, supply it with an ohm meter, and check what happens then....just have never done it. I have looked at some other posts here, and they have just started replacing stuff....kind of my way at some point, but I want to be smarter, and learn...if someone helps me through it.....I will be here vaccuming lint out, and checking back....thank you all!! new piece of news....there was a TON of lint inside the dryer....we had a birds nest at one point in the vent that went un noticed for a while...the vent is all clear now....the lint on top of the housing that has the heating coils was scorched...probably not a good thing right???...all the lint is cleared out now....saw a thread about a high temp cutoff that has to be replace if it is triggered?? the thermal fuse is probably blown, there's also a thermal cut-off and a thermostat which are usually replaced at the same time. check the element as well to make sure it didn't burn up. thermal fuse part # 3392519 $14.50 at sears kit # 279973 includes the thermal-cut off and the thermostat together $25 at sears if you need it the element is # 3387747 $57.50 at sears Parts Accessories | Shop Find Lawn Garden, Appliance Parts at Sears PartsDirect | SearsPartsDirect.com let us know how you make out. thanks. its not the thermal fuse. if it was bad then the motor would not turn. my moneys on the element. measure the resistance before you buy any parts OK.......how do I do that?? I know the dryer is unplugged, and I have access tot he coils.........what then? Where do I touch the 2 probes....sorry for being a nube on electricity...I need to take a class on basics of using an electrical tester. also...how do I take the element out on this model...obviously nothing in the users manual...anyone have a link to a blow up?? OK put OHM meter on each of the coil wires right from connector, and it didn't move..stayed at infinity....the housing registered 0....it is unplugged of course...does that mean the coils are toasted?? yes it is bad. you need to remove the shield in front of the element then remove the 1/4 screw that is half an inch behind the wire connectors. with gloves on put right hand on heater box and pull element out with left hand. OMG...thank you all!!!!!!!!!....it works..I feel like Tom Hanks on Castaway...I have made fire!.....little things make me happy, but nothing more than fixing something myself!!! Expensive little bugger, and hour wait at the sears service center..cold have got in E-bay for half, but the dear wife needs her machine...thanks again!!!

Related Posts:

• 
  Kenmore 70 series electric dryer wont heat need help fast
  
  Kenmore 70 series electric dryer won't heat, need help fast!Help! My dryer stopped working about three weeks ago, it wouldn't run at all. i figured out the reason it wasn't working was because the...
  


• 
  Kenmore dryer 90 series no heat
  
  Kenmore Dryer 90 series No HeatHow do I get to the heating element? It looks like they tack welded the back shut. Help!!!!! AJW Hi, Kenmore Dryer 90 series Kenmore is made by several different com...
  


• 
  Kenmore dryerno heat
  
  Kenmore Dryer=No heat!?I have an old Kenmore 60 series dryer (model # 66612690). I just finished replacing the heater element after checking the vents etc. While replacing the element I discovered...
  


• 
  Kenmore elite dryer no heat fix
  
  Kenmore Elite Dryer: No Heat FixHi Everyone, I spent over 5 hours working on and researching my no heat problem with my Kenmore Dryer model # 101.63942101 and have just discovered what the problem...
  


• 
  Kenmore elite washer model 11024944300
  
  Kenmore Elite Washer (Model 110.24944300)This washer is only about 5-6 years old. I couldn't locate the actual model number with Parts Accessories | Shop Find Lawn Garden, Appliance Parts at Sears...